304不銹鋼花紋板是通過機械設備在304不銹鋼板上進行壓紋加工，形成獨特形狀的鋼板。其表面圖案不均勻，具有良好的防滑性和耐久性。
304 stainless steel checkered plate is a steel plate with unique shape which is embossed on 304 stainless steel plate by mechanical equipment. Its surface pattern is uneven, with good skid resistance and durability.
隨著不銹鋼加工工藝的不斷升級，304不銹鋼花紋板的耐腐蝕性和抗壓性不斷增強，功能越來越強大，滿足了越來越多的場合需求。
With the continuous upgrading of stainless steel processing technology, the corrosion resistance and compression resistance of 304 stainless steel checkered plate are continuously enhanced, and the function is more and more powerful, meeting the needs of more and more occasions.
304不銹鋼花紋板常用于各種場所，常見的有以下幾種：
304 stainless steel checkered plates are often used in various places. The common ones are as follows:
(1)建筑施工用地
(1) Construction land
304不銹鋼花紋板經常出現在施工現場。它們會放置在大卡車頻繁進出的路段。有時候大卡車進出時，如果地面不平整，會對大卡車產生顛簸，從而增加地面的承載壓力，對路面造成一定的損壞。但如果把304不銹鋼花紋板放置在兩者之間，可以減輕地面的一些負擔，從而保護地面。
304 stainless steel checkered plates often appear on the construction site. They will be placed in sections where large trucks frequently enter and leave. Sometimes when large trucks go in and out, if the ground is uneven, it will bump the large trucks, thus increasing the bearing pressure on the ground and causing certain damage to the road surface. However, if the 304 stainless steel checkered plate is placed between the two, it can reduce some of the burden on the ground and protect the ground.
(2)樓梯踏步
(2) Stair step
304不銹鋼花紋板也廣泛應用于樓梯踏步中。由于其具有良好的防滑防腐性能，美觀耐用，可以避免水泥臺階或瓷磚臺階的缺點，更換頻率低，性價比相對較高。
304 stainless steel checkered plate is also widely used in stair steps. Due to its good anti-skid and anti-corrosion performance, beautiful and durable, it can avoid the shortcomings of cement steps or ceramic tile steps, with low replacement frequency and relatively high cost performance.
(3)室內裝潢
(3) Interior decoration
在工業風格的裝飾設計中，一些室內樓梯會選擇鋪設304不銹鋼花紋板，因為成本低，耐用性好，結構穩定，承載力強，金屬質感明顯，可以讓房子凸顯工業風格。超聲波清洗機的超聲波發生器具有以下特點：
In the decoration design of industrial style, some indoor stairs will choose to lay 304 stainless steel checkered plates. Because of low cost, good durability, stable structure, strong bearing capacity and obvious metal texture, the house can highlight the industrial style. The ultrasonic generator of the ultrasonic cleaning machine has the following characteristics:
（1） 換能器的諧振頻率和阻抗隨著清洗液的深度而發生很大變化。然而，事實表明，在向儲罐中加入一定量的清洗工件后，它們可以相對穩定在一定數值。
(1) The resonant frequency and impedance of the transducer vary greatly with the depth of the cleaning solution. However, facts show that after adding a certain amount of cleaning workpieces to the storage tank, they can be relatively stable at a certain value.
（2） 一般來說，由于清洗負荷變化小，不需要復頻自動跟蹤電路。
(2) Generally speaking, due to the small change of cleaning load, the complex frequency automatic tracking circuit is not required.
（3） 大多數實用的超聲波發生器采用大功率自激反射振蕩器。
(3) Most practical ultrasonic generators use high-power self-excited reflection oscillators.
超聲波清洗機使用的換能器主要有磁致伸縮換能器和壓電換能器。
The transducers used in ultrasonic cleaning machines mainly include magnetostrictive transducers and piezoelectric transducers.
磁致伸縮換能器，大多數國際上使用的磁致伸縮換能器都是由鎳片制成的窗口換能器，這些鎳片是銀焊接在清洗筒底部，然后在窗口上纏繞一定數量的線圈。該傳感器能承受大功率，可靠性好，使用壽命長。缺點是效率低于壓電換能器，且原材料鎳片價格昂貴；
Magnetostrictive transducers, most of the magnetostrictive transducers used internationally are window transducers made of nickel sheets, which are silver welded at the bottom of the cleaning cylinder, and then wound with a certain number of coils on the window. The sensor can bear high power, has good reliability and long service life. The disadvantage is that the efficiency is lower than that of piezoelectric transducer, and the raw material nickel sheet is expensive;
壓電式換能器。目前，國內外超聲波清洗機大多采用L型結構的壓電換能器。這種換能器一般由兩片壓電陶瓷片組成。清洗機使用多個傳感器，這些傳感器通過粘合劑連接到清洗滾筒的底部，并平行連接，形成清洗機的傳感器。傳感器元件之間的距離，對于20khz的頻率，一般為5-10mm。如果太大，則容易產生鋸齒形振動，振動板被侵蝕，輻射面減小。
Piezoelectric transducer. At present, most ultrasonic cleaning machines at home and abroad use L-shaped piezoelectric transducers. The transducer is generally composed of two piezoelectric ceramic plates. The cleaning machine uses multiple sensors, which are connected to the bottom of the cleaning drum through adhesive and connected in parallel to form the sensor of the cleaning machine. The distance between sensor elements is generally 5-10mm for 20kHz frequency. If it is too large, it is easy to produce sawtooth vibration, the vibrating plate is eroded, and the radiation surface is reduced.
所以，通用超聲清洗機清洗零件適用性強，已廣泛應用于光學、機械、汽車、航空、核工業、汽車電子、醫療設備等諸多行業。而專用超聲波清洗機主要安裝在某些特定工件清洗的生產流水線上。目前，還有一種超聲汽相清洗機，它是選用有機溶劑作為清洗液，具有極強的溶解污垢的能力，用于清洗半導體晶片等凈治度要求特別高的物件。
Therefore, the universal ultrasonic cleaning machine has strong applicability for cleaning parts, and has been widely used in many industries, such as optics, machinery, automobile, aviation, nuclear industry, automotive electronics, medical equipment and so on. The special ultrasonic cleaning machine is mainly installed on the production line for cleaning some specific workpieces. At present, there is also an ultrasonic vapor cleaning machine, which uses organic solvent as the cleaning fluid and has a strong ability to dissolve dirt. It is used to clean objects with particularly high cleanliness requirements such as semiconductor chips.
本文的精彩內容由不銹鋼花紋板供知識提供，本網站還有很多的精彩內容，更多的內容您可以點擊進入：http://www.fgmceramic.com我們有專門的客服為您解答問題
The wonderful content of this article is provided by stainless steel checkered plates. There are many wonderful content on this website. You can click to enter more content: http://www.fgmceramic.com We have special customer service to answer your questions
